• Anatomy
• Species
• Bottle Care
• Collecting Bottles

• Removing Labels
• Cutting Bottles
• Making Holes
• Building a Bottle Growing System

Anatomy: The first step in any construction project is to understand your materials. Almost all soda bottles taper at the shoulder and hip. Because of this shape, you can test the tapered ends inside the straight sides of another bottle.

Removing labels: Once you have collected bottles, you will need to remove the labels. Most labels are attached by a heat-sensitive glue. Resist ripping off the labels, or you may end up with many small pieces of label stuck to the bottle.

An inexpensive hair dryer will remove the label and base from your bottle in a jiffy. Set the hair dryer on low. Hold your bottle about 10 cm away from a blowing nozzle, and move it rapidly up and down so that the air warms the seam of the label. Gently pull on an edge of the label until you feel the glue begin to give. This takes about 4 seconds.

Bottles are made from PETE (polyethylene teraphthalate). This is a generally inert plastic, but it will warp easily if overheated, so keep the bottle moving. Leave the bottle cap on or fill the bottle with water first to prevent warping.

A quieter way to remove the label and base from your bottle is to fill it about 1/4 full with very warm water (49 - 65 degrees C or 120 - 150 degrees F; hotter than this may warp your bottle). Cap the bottle in order to retain pressure inside so the bottle doesn't crumple, and tip it on its side to warm the glued seam. After a few seconds tug on a label corner.

Glue is often left on the bottle after the label is removed. If this offends your aesthetic sensibilities, rub a small amount of peanut butter onto the glue. As you rub, the oil in the peanut butter causes the glue to ball up so it can be pulled off (no kidding, crunchy works best). If you are really into the clean bottle look, wash your bottles with soap and warm water and dry them – they'll shine!

Cutting bottles: There are only so many ways you can cut a bottle; above the shoulder, below the shoulder, above the hip and below the hip, and only so many things you can do with each piece you create.

The easiest way to cut a bottle is to cut along a marked line with scissors. Once you have decided where to cut a bottle, place it on its side in the corner of an empty drawer, tray, or box — shallow cardboard flats and computer printer paper box tops work well. Brace the bottom of the bottle against a corner of the box. Rest a pen or wax pencil against the edge of the box, so the tip rests against the bottle where you want your cutting line. Slowly turn the bottle. Two people make this job easy.

We use erasable felt tip pens or wax pencils to make cutting lines because they don't smear and can be easily removed. Make sure your bottle is dry before marking. If you want lines that last, use a permanent marker.

Draw all of your cutting lines first (it's hard to do once the bottles have been cut), and then use a cutting blade to begin the bottle cuts. You only need a cut big enough to insert the top arm of a scissors. You will make a smoother cut with the top arm of the scissors inside the bottle, so insert the top arm into your initial cut and snip around, following your cutting line. Don't worry about ragged edges; they are easy to snip away with scissors once the bottle is in pieces.

A woodworking awl is quite effective at making small holes in bottles and bottle caps. If an awl is pushed all the way through a surface, it will create a hole several millimeters wide, enough for fruit flies to pass through. Awls are particularly sharp, so place a piece of wood underneath whatever you are poking and watch your fingers.

A tapered reamer, available at the hardware store, is excellent for enlarging holes. Normally used for creating holes in sheet metal, it will easily make a hole in plastic up to 1 cm in diameter. Since the reamer has a blunt tip, begin your hole with an awl or poke.

If you are preparing materials for many students, a drill press is the most efficient tool if you have access to one. Regular spiral fluted drill bits work well, and sharp "brad" pointed bits will wander less on the surface of the plastic as you start your hole. For holes larger than 1 cm, flat wood bits with spurs on the blade tips work best.

Alternately, several layers of aluminum foil can be attached by a rubberband in place of the cap, and a hole can be easily punched through the foil.

For many, many more ideas about using bottles in science, visit www.bottlebiology.org.